瑞萨RZ/G2L平台 初起动（SD卡启动）
文章目录
- 一 准备条件
- 1 工具
- 2 硬件
- 3 镜像
- 二 烧录SD卡启动盘
- 三 写Bootloader
- 1 烧录文件
- 2 启动烧录
- 3 烧录
- 四 启动设置
一 准备条件
1 工具
** BalenaEtcher（俗称“ Etcher”），是一款快速将系统镜像文件（ .iso 或 .img 或 .zip或.wic）刻录到usb等设备的启动盘制作工具。balenaEtcher基于 Electron 框架开发，支持windows,macOs和linux系统。类似的工具还有Win32 Disk Imager等，该工具的下载链接：https://etcher.balena.io/
** Tera Term是一款虚似的终端软件，一般用以全自动实行与从PC进行的远程桌面连接有关的每日任务，适用TCP/IP网络联接和串口通信接口方式，适用SSH/Telnet以及他服务项目，可订制自身的开发语言加上拓展作用。类似的如putty、MobaXterm等，该工具的官方连接：http://www.teraterm.net/（不知什么原因，打不开），可以通过如下连接下载：
https://pan.baidu.com/s/1gW_5PCJzloKoclcaBPXy1Q
提取码：h8ny
2 硬件
** USB type C charger
** USB type C to type C cable
** micro SD UHI-Class10 (8GB or more)
** USB cable (USB Type-A- Micro USB Type-B)
** micro-HDMI to HDMI cable
**
3 镜像
RZ/G2L Pre-built Images (RZG2L_VLP3.0.5_Pre-built_Images_EN.zip)
二 烧录SD卡启动盘
使用BalenaEtcher工具，将Images烧录到SD卡上。即打开工具，依次选择添加镜像–》选择SD卡–》启动烧录
最后烧录成功显示如下
三 写Bootloader
1 烧录文件
SD卡烧录成功后，在boot分区会有如下几样东西，其中3样（lash_Writer_SCIF_RZG2L_SMARC_PMIC_DDR4_2GB_1PCS.mot, bl2_bp-smarc-rzg2l_pmic.srec and fip-smarc-rzg2l_pmic.srec）是要通过Tera Term经串口烧录到系统中
2 启动烧录
RZ/G2L参考板的硬件大体如下所示，连接对应的接线后，做如下操作，进入烧录模式：
1）上电（CN6），此时 LED1(VBUS Power ON) and LED3 (Module PWR On) 2个LED点亮
2）确认SW11设置为OFF/ON/OFF/ON和SW1设置为ON/OFF
3）长按SW9 大约2s，LED4(Carrier PWR On)点亮
3 烧录
1）通过 Tera Term软件的 “File” > “Send file”，依次选择要烧录的文件烧录
2）如下是选择文件
3）如下是烧录过程
4 ）如下是完整的烧录过程打印
四 启动设置
1）Please change the SW11 as below (SW11-2 ON→OFF).
2）Insert your microSD card to the slot (CN10) on the carry board.
3）Turn on the power of the board by pressing the power button SW9.此时，启动会失败
重新设置环境变量，正常启动
4）完整的启动打印，启动后，显示weston界面
NOTICE: BL2: v2.9(release):c314a39-dirty
[11-04-54.895]NOTICE: BL2: Built : 14:49:18, Sep 19 2023
[11-04-54.936]NOTICE: BL2: Booting BL31
[11-04-54.937]NOTICE: BL31: v2.9(release):c314a39-dirty
[11-04-54.937]NOTICE: BL31: Built : 14:49:18, Sep 19 2023
[11-04-55.040]
[11-04-55.040]
[11-04-55.040]U-Boot 2021.10 (Sep 20 2023 - 02:21:30 +0000)
[11-04-55.040]
[11-04-55.040]CPU: Renesas Electronics CPU rev 1.0
[11-04-55.040]Model: smarc-rzg2l
[11-04-55.153]DRAM: 1.9 GiB
[11-04-55.231]WDT: watchdog@0000000012800800
[11-04-55.231]WDT: Started with servicing (60s timeout)
[11-04-55.231]MMC: sd@11c00000: 0, sd@11c10000: 1
[11-04-56.088]Loading Environment from MMC... OK
[11-04-56.106]In: serial@1004b800
[11-04-56.107]Out: serial@1004b800
[11-04-56.107]Err: serial@1004b800
[11-04-56.107]U-boot WDT started!
[11-04-56.164]Net:
[11-04-56.164]Error: ethernet@11c20000 address not set.
[11-04-56.164]No ethernet found.
[11-04-56.164]
[11-04-58.165]Hit any key to stop autoboot: 0
[11-04-58.165]## Resetting to default environment
[11-04-58.325]switch to partitions #0, OK
[11-04-58.325]mmc1 is current device
[11-04-59.908]20068864 bytes read in 1579 ms (12.1 MiB/s)
[11-04-59.935]38594 bytes read in 6 ms (6.1 MiB/s)
[11-04-59.935]Error: Bad gzipped data
[11-04-59.935]Moving Image from 0x48080000 to 0x48200000, end=495a0000
[11-05-00.029]## Flattened Device Tree blob at 48000000
[11-05-00.029] Booting using the fdt blob at 0x48000000
[11-05-00.030] Loading Device Tree to 0000000057ff3000, end 0000000057fff6c1 ... OK
[11-05-00.030]
[11-05-00.035]Starting kernel ...
[11-05-00.035]
[11-05-00.132][ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[11-05-00.132][ 0.000000] Linux version 5.10.184-cip36-yocto-standard (oe-user@oe-host) (aarch64-poky-linux-gcc (GCC) 8.3.0, GNU ld (GNU Binutils) 2.31.1) #1 SMP PREEMPT Tue Apr 5 23:00:00 UTC 2011
[11-05-00.133][ 0.000000] Machine model: Renesas SMARC EVK based on r9a07g044l2
[11-05-00.133][ 0.000000] earlycon: scif0 at MMIO 0x000000001004b800 (options '115200n8')
[11-05-00.133][ 0.000000] printk: bootconsole [scif0] enabled
[11-05-00.133][ 0.000000] efi: UEFI not found.
[11-05-00.133][ 0.000000] Reserved memory: created CMA memory pool at 0x0000000058000000, size 256 MiB
[11-05-00.134][ 0.000000] OF: reserved mem: initialized node linux,cma@58000000, compatible id shared-dma-pool
[11-05-00.136][ 0.000000] Reserved memory: created CMA memory pool at 0x0000000068000000, size 128 MiB
[11-05-00.136][ 0.000000] OF: reserved mem: initialized node linux,multimedia, compatible id shared-dma-pool
[11-05-00.152][ 0.000000] Zone ranges:
[11-05-00.190][ 0.000000] DMA [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-00.190][ 0.000000] DMA32 empty
[11-05-00.190][ 0.000000] Normal empty
[11-05-00.190][ 0.000000] Movable zone start for each node
[11-05-00.190][ 0.000000] Early memory node ranges
[11-05-00.194][ 0.000000] node 0: [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-00.194][ 0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-00.304][ 0.000000] psci: probing for conduit method from DT.
[11-05-00.304][ 0.000000] psci: PSCIv1.1 detected in firmware.
[11-05-00.304][ 0.000000] psci: Using standard PSCI v0.2 function IDs
[11-05-00.305][ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[11-05-00.305][ 0.000000] psci: SMC Calling Convention v1.2
[11-05-00.305][ 0.000000] percpu: Embedded 23 pages/cpu s55896 r8192 d30120 u94208
[11-05-00.306][ 0.000000] Detected VIPT I-cache on CPU0
[11-05-00.306][ 0.000000] CPU features: detected: GIC system register CPU interface
[11-05-00.306][ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[11-05-00.307][ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 483840
[11-05-00.307][ 0.000000] Kernel command line: rw rootwait earlycon root=/dev/mmcblk1p2 wdt_overflow=0
[11-05-00.307][ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[11-05-00.307][ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[11-05-00.308][ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[11-05-00.472][ 0.000000] Memory: 1512672K/1966080K available (12608K kernel code, 1102K rwdata, 3664K rodata, 2112K init, 429K bss, 60192K reserved, 393216K cma-reserved)
[11-05-00.472][ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[11-05-00.472][ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[11-05-00.473][ 0.000000] rcu: RCU event tracing is enabled.
[11-05-00.473][ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[11-05-00.473][ 0.000000] Trampoline variant of Tasks RCU enabled.
[11-05-00.473][ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[11-05-00.473][ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[11-05-00.473][ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[11-05-00.473][ 0.000000] GICv3: 480 SPIs implemented
[11-05-00.473][ 0.000000] GICv3: 0 Extended SPIs implemented
[11-05-00.473][ 0.000000] GICv3: Distributor has no Range Selector support
[11-05-00.474][ 0.000000] GICv3: 16 PPIs implemented
[11-05-00.474][ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000011940000
[11-05-00.474][ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[11-05-00.474][ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[11-05-00.475][ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[11-05-00.476][ 0.008228] Console: colour dummy device 80x25
[11-05-00.476][ 0.012695] printk: console [tty0] enabled
[11-05-00.476][ 0.016812] printk: bootconsole [scif0] disabled
[11-05-02.161][ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[11-05-02.161][ 0.000000] Linux version 5.10.184-cip36-yocto-standard (oe-user@oe-host) (aarch64-poky-linux-gcc (GCC) 8.3.0, GNU ld (GNU Binutils) 2.31.1) #1 SMP PREEMPT Tue Apr 5 23:00:00 UTC 2011
[11-05-02.161][ 0.000000] Machine model: Renesas SMARC EVK based on r9a07g044l2
[11-05-02.162][ 0.000000] earlycon: scif0 at MMIO 0x000000001004b800 (options '115200n8')
[11-05-02.162][ 0.000000] printk: bootconsole [scif0] enabled
[11-05-02.162][ 0.000000] efi: UEFI not found.
[11-05-02.162][ 0.000000] Reserved memory: created CMA memory pool at 0x0000000058000000, size 256 MiB
[11-05-02.162][ 0.000000] OF: reserved mem: initialized node linux,cma@58000000, compatible id shared-dma-pool
[11-05-02.163][ 0.000000] Reserved memory: created CMA memory pool at 0x0000000068000000, size 128 MiB
[11-05-02.163][ 0.000000] OF: reserved mem: initialized node linux,multimedia, compatible id shared-dma-pool
[11-05-02.163][ 0.000000] Zone ranges:
[11-05-02.163][ 0.000000] DMA [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-02.163][ 0.000000] DMA32 empty
[11-05-02.163][ 0.000000] Normal empty
[11-05-02.163][ 0.000000] Movable zone start for each node
[11-05-02.163][ 0.000000] Early memory node ranges
[11-05-02.163][ 0.000000] node 0: [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-02.163][ 0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-02.164][ 0.000000] psci: probing for conduit method from DT.
[11-05-02.164][ 0.000000] psci: PSCIv1.1 detected in firmware.
[11-05-02.164][ 0.000000] psci: Using standard PSCI v0.2 function IDs
[11-05-02.165][ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[11-05-02.165][ 0.000000] psci: SMC Calling Convention v1.2
[11-05-02.166][ 0.000000] percpu: Embedded 23 pages/cpu s55896 r8192 d30120 u94208
[11-05-02.166][ 0.000000] Detected VIPT I-cache on CPU0
[11-05-02.166][ 0.000000] CPU features: detected: GIC system register CPU interface
[11-05-02.166][ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[11-05-02.166][ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 483840
[11-05-02.166][ 0.000000] Kernel command line: rw rootwait earlycon root=/dev/mmcblk1p2 wdt_overflow=0
[11-05-02.167][ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[11-05-02.167][ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[11-05-02.167][ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[11-05-02.167][ 0.000000] Memory: 1512672K/1966080K available (12608K kernel code, 1102K rwdata, 3664K rodata, 2112K init, 429K bss, 60192K reserved, 393216K cma-reserved)
[11-05-02.168][ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[11-05-02.168][ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[11-05-02.168][ 0.000000] rcu: RCU event tracing is enabled.
[11-05-02.168][ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[11-05-02.168][ 0.000000] Trampoline variant of Tasks RCU enabled.
[11-05-02.168][ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[11-05-02.168][ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[11-05-02.168][ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[11-05-02.168][ 0.000000] GICv3: 480 SPIs implemented
[11-05-02.169][ 0.000000] GICv3: 0 Extended SPIs implemented
[11-05-02.169][ 0.000000] GICv3: Distributor has no Range Selector support
[11-05-02.170][ 0.000000] GICv3: 16 PPIs implemented
[11-05-02.170][ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000011940000
[11-05-02.171][ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[11-05-02.171][ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[11-05-02.171][ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[11-05-02.171][ 0.008228] Console: colour dummy device 80x25
[11-05-02.171][ 0.012695] printk: console [tty0] enabled
[11-05-02.171][ 0.016812] printk: bootconsole [scif0] disabled
[11-05-02.172][ 0.021482] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[11-05-02.172][ 0.021505] pid_max: default: 32768 minimum: 301
[11-05-02.172][ 0.021646] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[11-05-02.504][ 0.021667] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[11-05-02.504][ 0.023331] rcu: Hierarchical SRCU implementation.
[11-05-02.505][ 0.024015] Detected Renesas RZ/G2L r9a07g044 Rev 1
[11-05-02.505][ 0.024283] EFI services will not be available.
[11-05-02.505][ 0.024561] smp: Bringing up secondary CPUs ...
[11-05-02.505][ 0.025077] Detected VIPT I-cache on CPU1
[11-05-02.505][ 0.025119] GICv3: CPU1: found redistributor 100 region 0:0x0000000011960000
[11-05-02.505][ 0.025171] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[11-05-02.505][ 0.025298] smp: Brought up 1 node, 2 CPUs
[11-05-02.505][ 0.025341] SMP: Total of 2 processors activated.
[11-05-02.506][ 0.025352] CPU features: detected: Privileged Access Never
[11-05-02.506][ 0.025361] CPU features: detected: LSE atomic instructions
[11-05-02.506][ 0.025371] CPU features: detected: User Access Override
[11-05-02.506][ 0.025382] CPU features: detected: 32-bit EL0 Support
[11-05-02.506][ 0.025392] CPU features: detected: Common not Private translations
[11-05-02.506][ 0.025403] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[11-05-02.506][ 0.025420] CPU features: detected: CRC32 instructions
[11-05-02.506][ 0.025430] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[11-05-02.506][ 0.025442] CPU features: detected: 32-bit EL1 Support
[11-05-02.507][ 0.043629] CPU: All CPU(s) started at EL1
[11-05-02.507][ 0.043714] alternatives: patching kernel code
[11-05-02.507][ 0.046176] devtmpfs: initialized
[11-05-02.507][ 0.052375] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[11-05-02.508][ 0.052432] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[11-05-02.508][ 0.061800] pinctrl core: initialized pinctrl subsystem
[11-05-02.508][ 0.062636] DMI not present or invalid.
[11-05-02.508][ 0.063120] NET: Registered protocol family 16
[11-05-02.508][ 0.064638] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[11-05-02.508][ 0.064807] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[11-05-02.509][ 0.064970] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[11-05-02.509][ 0.065101] audit: initializing netlink subsys (disabled)
[11-05-02.509][ 0.065443] audit: type=2000 audit(0.056:1): state=initialized audit_enabled=0 res=1
[11-05-02.509][ 0.066007] thermal_sys: Registered thermal governor 'step_wise'
[11-05-02.509][ 0.066376] cpuidle: using governor menu
[11-05-02.509][ 0.066575] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[11-05-02.509][ 0.066665] ASID allocator initialised with 65536 entries
[11-05-02.509][ 0.094397] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[11-05-02.510][ 0.094437] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[11-05-02.510][ 0.094451] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[11-05-02.510][ 0.094464] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[11-05-02.510][ 0.096378] cryptd: max_cpu_qlen set to 1000
[11-05-02.510][ 0.165991] raid6: neonx8 gen() 2132 MB/s
[11-05-02.510][ 0.234049] raid6: neonx8 xor() 1641 MB/s
[11-05-02.510][ 0.302126] raid6: neonx4 gen() 2192 MB/s
[11-05-02.511][ 0.370190] raid6: neonx4 xor() 1630 MB/s
[11-05-02.512][ 0.438259] raid6: neonx2 gen() 2092 MB/s
[11-05-02.513][ 0.506325] raid6: neonx2 xor() 1493 MB/s
[11-05-02.513][ 0.574402] raid6: neonx1 gen() 1807 MB/s
[11-05-02.513][ 0.642460] raid6: neonx1 xor() 1255 MB/s
[11-05-02.513][ 0.710527] raid6: int64x8 gen() 1510 MB/s
[11-05-02.513][ 0.778572] raid6: int64x8 xor() 772 MB/s
[11-05-02.513][ 0.846659] raid6: int64x4 gen() 1643 MB/s
[11-05-02.513][ 0.914695] raid6: int64x4 xor() 837 MB/s
[11-05-02.513][ 0.982750] raid6: int64x2 gen() 1484 MB/s
[11-05-02.514][ 1.050816] raid6: int64x2 xor() 748 MB/s
[11-05-02.514][ 1.118878] raid6: int64x1 gen() 1148 MB/s
[11-05-02.514][ 1.186935] raid6: int64x1 xor() 559 MB/s
[11-05-02.514][ 1.186947] raid6: using algorithm neonx4 gen() 2192 MB/s
[11-05-02.514][ 1.186958] raid6: .... xor() 1630 MB/s, rmw enabled
[11-05-02.514][ 1.186969] raid6: using neon recovery algorithm
[11-05-02.514][ 1.190887] iommu: Default domain type: Translated
[11-05-02.514][ 1.191719] vgaarb: loaded
[11-05-02.514][ 1.192129] SCSI subsystem initialized
[11-05-02.514][ 1.192601] usbcore: registered new interface driver usbfs
[11-05-02.515][ 1.192656] usbcore: registered new interface driver hub
[11-05-02.515][ 1.192695] usbcore: registered new device driver usb
[11-05-02.850][ 1.193530] mc: Linux media interface: v0.10
[11-05-02.850][ 1.193566] videodev: Linux video capture interface: v2.00
[11-05-02.850][ 1.193644] pps_core: LinuxPPS API ver. 1 registered
[11-05-02.851][ 1.193656] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[11-05-02.851][ 1.193681] PTP clock support registered
[11-05-02.851][ 1.193718] EDAC MC: Ver: 3.0.0
[11-05-02.851][ 1.195143] Advanced Linux Sound Architecture Driver Initialized.
[11-05-02.851][ 1.196081] clocksource: Switched to clocksource arch_sys_counter
[11-05-02.851][ 1.196326] VFS: Disk quotas dquot_6.6.0
[11-05-02.851][ 1.196399] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[11-05-02.852][ 1.202464] NET: Registered protocol family 2
[11-05-02.852][ 1.202717] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[11-05-02.852][ 1.203990] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[11-05-02.852][ 1.204115] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[11-05-02.852][ 1.204229] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
[11-05-02.852][ 1.204512] TCP: Hash tables configured (established 16384 bind 16384)
[11-05-02.852][ 1.204692] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[11-05-02.853][ 1.204737] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[11-05-02.853][ 1.204932] NET: Registered protocol family 1
[11-05-02.853][ 1.205540] RPC: Registered named UNIX socket transport module.
[11-05-02.853][ 1.205570] RPC: Registered udp transport module.
[11-05-02.854][ 1.205581] RPC: Registered tcp transport module.
[11-05-02.854][ 1.205591] RPC: Registered tcp NFSv4.1 backchannel transport module.
[11-05-02.855][ 1.205610] PCI: CLS 0 bytes, default 64
[11-05-02.855][ 1.206468] kvm [1]: HYP mode not available
[11-05-02.855][ 1.208422] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[11-05-02.855][ 1.214381] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[11-05-02.855][ 1.215141] NFS: Registering the id_resolver key type
[11-05-02.855][ 1.215201] Key type id_resolver registered
[11-05-02.855][ 1.215213] Key type id_legacy registered
[11-05-02.855][ 1.215306] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[11-05-02.855][ 1.215332] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[11-05-02.856][ 1.215368] jffs2: version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
[11-05-02.856][ 1.252414] xor: measuring software checksum speed
[11-05-02.856][ 1.256797] 8regs : 2281 MB/sec
[11-05-02.856][ 1.260229] 32regs : 2887 MB/sec
[11-05-02.856][ 1.264263] arm64_neon : 2450 MB/sec
[11-05-02.856][ 1.264275] xor: using function: 32regs (2887 MB/sec)
[11-05-02.856][ 1.264352] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[11-05-02.857][ 1.264542] io scheduler mq-deadline registered
[11-05-02.857][ 1.264560] io scheduler kyber registered
[11-05-02.857][ 1.266463] poeg-rzg2l 10048800.poega: RZ/G2L POEG Driver probed
[11-05-02.857][ 1.266859] poeg-rzg2l 10048c00.poegb: RZ/G2L POEG Driver probed
[11-05-02.857][ 1.267175] poeg-rzg2l 10049000.poegc: RZ/G2L POEG Driver probed
[11-05-02.857][ 1.267337] poeg-rzg2l 10049400.poegd: RZ/G2L POEG Driver probed
[11-05-02.857][ 1.310829] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[11-05-02.858][ 1.311996] SuperH (H)SCI(F) driver initialized
[11-05-02.858][ 1.323921] loop: module loaded
[11-05-02.858][ 1.327252] tun: Universal TUN/TAP device driver, 1.6
[11-05-02.858][ 1.327537] CAN device driver interface
[11-05-02.858][ 1.328162] e1000e: Intel(R) PRO/1000 Network Driver
[11-05-02.859][ 1.328182] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[11-05-02.859][ 1.328841] VFIO - User Level meta-driver version: 0.3
[11-05-02.859][ 1.329114] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[11-05-02.859][ 1.329134] ehci-pci: EHCI PCI platform driver
[11-05-02.859][ 1.329195] ehci-platform: EHCI generic platform driver
[11-05-02.859][ 1.329919] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[11-05-02.859][ 1.329973] ohci-pci: OHCI PCI platform driver
[11-05-02.860][ 1.330057] ohci-platform: OHCI generic platform driver
[11-05-02.860][ 1.331254] usbcore: registered new interface driver usb-storage
[11-05-02.860][ 1.331788] renesas_usbhs 11c60000.usb: host probed
[11-05-02.860][ 1.331811] renesas_usbhs 11c60000.usb: no transceiver found
[11-05-02.860][ 1.331953] renesas_usbhs 11c60000.usb: gadget probed
[11-05-03.198][ 1.332149] renesas_usbhs 11c60000.usb: platform init failed.
[11-05-03.198][ 1.332300] renesas_usbhs 11c60000.usb: probe failed (-517)
[11-05-03.198][ 1.333324] usbcore: registered new interface driver usbtouchscreen
[11-05-03.198][ 1.333393] i2c /dev entries driver
[11-05-03.198][ 1.338273] rzg2l-csi2 10830400.csi2: 2 lanes found
[11-05-03.198][ 1.342373] device-mapper: ioctl: 4.43.0-ioctl (2020-10-01) initialised: dm-devel@redhat.com
[11-05-03.199][ 1.342956] EDAC rzg2l-edac: IO mapped reg addr: 0x11410000
[11-05-03.199][ 1.343255] EDAC MC0: Giving out device to module rzg2l-edac controller renesas,r9a07g044-edac: DEV 11410000.edac (INTERRUPT)
[11-05-03.199][ 1.346094] ledtrig-cpu: registered to indicate activity on CPUs
[11-05-03.199][ 1.346147] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[11-05-03.199][ 1.346589] renesas_mtu3 10001200.timer: ch0: used as clock source
[11-05-03.199][ 1.346616] clocksource: 10001200.timer: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 18664368 ns
[11-05-03.199][ 1.346638] renesas_mtu3 10001200.timer: ch1: used for clock events
[11-05-03.199][ 1.346660] renesas_mtu3 10001200.timer: Renesas MTU3 driver probed
[11-05-03.200][ 1.347277] clocksource: timer@12801400: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns
[11-05-03.200][ 1.347314] sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 21474836475ns
[11-05-03.200][ 1.347335] /soc/timer@12801400: used for clocksource
[11-05-03.200][ 1.347669] /soc/timer@12801800: used for clock events
[11-05-03.200][ 1.348681] usbcore: registered new interface driver usbhid
[11-05-03.200][ 1.348710] usbhid: USB HID core driver
[11-05-03.201][ 1.349364] optee: probing for conduit method.
[11-05-03.201][ 1.349392] optee: api uid mismatch
[11-05-03.201][ 1.349415] optee: probe of firmware:optee failed with error -22
[11-05-03.202][ 1.351800] IPVS: Registered protocols (TCP, UDP)
[11-05-03.203][ 1.351881] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[11-05-03.203][ 1.352113] IPVS: ipvs loaded.
[11-05-03.203][ 1.352133] IPVS: [rr] scheduler registered.
[11-05-03.203][ 1.352446] Initializing XFRM netlink socket
[11-05-03.203][ 1.352869] NET: Registered protocol family 10
[11-05-03.203][ 1.353885] Segment Routing with IPv6
[11-05-03.203][ 1.354023] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[11-05-03.203][ 1.354717] NET: Registered protocol family 17
[11-05-03.203][ 1.354823] Bridge firewalling registered
[11-05-03.203][ 1.354838] can: controller area network core
[11-05-03.203][ 1.354901] NET: Registered protocol family 29
[11-05-03.204][ 1.354918] can: raw protocol
[11-05-03.204][ 1.354938] can: broadcast manager protocol
[11-05-03.204][ 1.354957] can: netlink gateway - max_hops=1
[11-05-03.204][ 1.355134] Key type dns_resolver registered
[11-05-03.204][ 1.355658] registered taskstats version 1
[11-05-03.204][ 1.356933] Btrfs loaded, crc32c=crc32c-generic
[11-05-03.204][ 1.364812] thermal emergency: set temperature to 110 celsius
[11-05-03.204][ 1.364977] thermal emergency: shutdown target cpus 1
[11-05-03.204][ 1.364993] thermal emergency: freq scaled target cpus 0
[11-05-03.204][ 1.367161] gpio-153 (gpio_sd0_pwr_en): hogged as output/high
[11-05-03.204][ 1.367209] gpio-449 (sd0_dev_sel): hogged as output/high
[11-05-03.205][ 1.367239] gpio-458 (can0_stb): hogged as output/low
[11-05-03.205][ 1.367265] gpio-459 (can1_stb): hogged as output/low
[11-05-03.205][ 1.367293] gpio-434 (sd1_pwr_en): hogged as output/high
[11-05-03.205][ 1.367722] gpio gpiochip0: (11030000.pinctrl): detected irqchip that is shared with multiple gpiochips: please fix the driver.
[11-05-03.206][ 1.368048] pinctrl-rzg2l 11030000.pinctrl: pinctrl-rzg2l support registered
[11-05-03.206][ 1.371316] gpt-rzg2l 10048400.gpt: Can use GTETRGA as POEG, reset_counter
[11-05-03.206][ 1.371358] gpt-rzg2l 10048400.gpt: Can use GTETRGB as POEG, reset_counter
[11-05-03.206][ 1.371379] gpt-rzg2l 10048400.gpt: Can use GTETRGC as POEG, reset_counter
[11-05-03.206][ 1.371398] gpt-rzg2l 10048400.gpt: Can use GTETRGD as POEG, reset_counter
[11-05-03.206][ 1.372048] gpt-rzg2l 10048400.gpt: RZ/G2L GPT Driver probed
[11-05-03.206][ 1.372748] 1004b800.serial: ttySC0 at MMIO 0x1004b800 (irq = 26, base_baud = 0) is a scif
[11-05-03.207][ 2.728230] printk: console [ttySC0] enabled
[11-05-03.207][ 2.735349] renesas_spi 1004b000.spi: DMA available
[11-05-03.207][ 2.740708] renesas_spi 1004b000.spi: probed
[11-05-03.207][ 2.746211] rcar_canfd 10050000.can: can_clk rate is 50000000
[11-05-03.268][ 2.752643] rcar_canfd 10050000.can: device registered (channel 0)
[11-05-03.268][ 2.758910] rcar_canfd 10050000.can: can_clk rate is 50000000
[11-05-03.269][ 2.765140] rcar_canfd 10050000.can: device registered (channel 1)
[11-05-03.269][ 2.771331] rcar_canfd 10050000.can: global operational state (clk 0, fdmode 1)
[11-05-03.269][ 2.779549] ravb 11c20000.ethernet: no valid MAC address supplied, using a random one
[11-05-03.269][ 2.790156] ravb 11c20000.ethernet eth0: Base address at 0x11c20000, 1e:d3:15:a9:48:d3, IRQ 131.
[11-05-03.270][ 2.799973] ravb 11c30000.ethernet: no valid MAC address supplied, using a random one
[11-05-03.274][ 2.810349] ravb 11c30000.ethernet eth1: Base address at 0x11c30000, 76:7b:a4:dc:60:e1, IRQ 134.
[11-05-03.317][ 2.844124] ehci-platform 11c50100.usb: EHCI Host Controller
[11-05-03.317][ 2.849848] ehci-platform 11c50100.usb: new USB bus registered, assigned bus number 1
[11-05-03.321][ 2.857816] ehci-platform 11c50100.usb: irq 139, io mem 0x11c50100
[11-05-03.361][ 2.876082] ehci-platform 11c50100.usb: USB 2.0 started, EHCI 1.10
[11-05-03.362][ 2.882921] hub 1-0:1.0: USB hub found
[11-05-03.362][ 2.886719] hub 1-0:1.0: 1 port detected
[11-05-03.362][ 2.891655] ehci-platform 11c70100.usb: EHCI Host Controller
[11-05-03.365][ 2.897368] ehci-platform 11c70100.usb: new USB bus registered, assigned bus number 2
[11-05-03.366][ 2.905287] ehci-platform 11c70100.usb: irq 140, io mem 0x11c70100
[11-05-03.413][ 2.924088] ehci-platform 11c70100.usb: USB 2.0 started, EHCI 1.10
[11-05-03.413][ 2.930911] hub 2-0:1.0: USB hub found
[11-05-03.413][ 2.934706] hub 2-0:1.0: 1 port detected
[11-05-03.413][ 2.939553] ohci-platform 11c50000.usb: Generic Platform OHCI controller
[11-05-03.413][ 2.946319] ohci-platform 11c50000.usb: new USB bus registered, assigned bus number 3
[11-05-03.417][ 2.954282] ohci-platform 11c50000.usb: irq 137, io mem 0x11c50000
[11-05-03.531][ 3.050732] hub 3-0:1.0: USB hub found
[11-05-03.531][ 3.054535] hub 3-0:1.0: 1 port detected
[11-05-03.531][ 3.059384] ohci-platform 11c70000.usb: Generic Platform OHCI controller
[11-05-03.532][ 3.066151] ohci-platform 11c70000.usb: new USB bus registered, assigned bus number 4
[11-05-03.535][ 3.074108] ohci-platform 11c70000.usb: irq 138, io mem 0x11c70000
[11-05-03.648][ 3.170722] hub 4-0:1.0: USB hub found
[11-05-03.649][ 3.174525] hub 4-0:1.0: 1 port detected
[11-05-03.649][ 3.179394] renesas_usbhs 11c60000.usb: host probed
[11-05-03.649][ 3.184330] renesas_usbhs 11c60000.usb: no transceiver found
[11-05-03.649][ 3.190104] renesas_usbhs 11c60000.usb: gadget probed
[11-05-03.653][ 3.195401] renesas_usbhs 11c60000.usb: probed
[11-05-03.882][ 3.244217] ov5645 0-003c: ov5645_write_reg: write reg error -6: reg=3103, val=11
[11-05-03.883][ 3.251718] ov5645 0-003c: could not set init registers
[11-05-03.883][ 3.256945] ov5645 0-003c: could not power up OV5645
[11-05-03.883][ 3.262297] i2c-riic 10058000.i2c: registered with 100000Hz bus speed
[11-05-03.883][ 3.277848] i2c-riic 10058400.i2c: registered with 100000Hz bus speed
[11-05-03.883][ 3.286202] raa215300 3-0012: RTC enabled
[11-05-03.884][ 3.290286] raa215300 3-0012: RAA215300 initialized
[11-05-03.884][ 3.295786] rtc-isl1208 3-006f: rtc power failure detected, please set clock.
[11-05-03.884][ 3.303208] rtc-isl1208 3-006f: Using external oscillator
[11-05-03.884][ 3.310337] rtc-isl1208 3-006f: registered as rtc0
[11-05-03.884][ 3.315496] rtc-isl1208 3-006f: setting system clock to 2000-01-01T00:00:00 UTC (946684800)
[11-05-03.884][ 3.329407] i2c-riic 10058c00.i2c: registered with 400000Hz bus speed
[11-05-03.884][ 3.339748] spi-nor spi1.0: mt25qu512a (65536 Kbytes)
[11-05-03.884][ 3.345566] 5 fixed-partitions partitions found on MTD device spi1.0
[11-05-03.884][ 3.351939] Creating 5 MTD partitions on "spi1.0":
[11-05-03.884][ 3.356724] 0x000000000000-0x000000080000 : "u-boot"
[11-05-03.885][ 3.362879] 0x000000080000-0x0000000c0000 : "env"
[11-05-03.885][ 3.368852] 0x0000000c0000-0x000000100000 : "dtb"
[11-05-03.885][ 3.374800] 0x000000800000-0x000001800000 : "rootfs"
[11-05-03.885][ 3.381019] 0x000002000000-0x000002100000 : "test-area"
[11-05-03.885][ 3.384308] renesas_sdhi_internal_dmac 11c00000.mmc: mmc0 base at 0x0000000011c00000, max clock rate 100 MHz
[11-05-03.885][ 3.392424] rz-ssi-pcm-audio 10049c00.ssi: DMA enabled
[11-05-03.885][ 3.396315] renesas_sdhi_internal_dmac 11c10000.mmc: mmc1 base at 0x0000000011c10000, max clock rate 100 MHz
[11-05-03.886][ 3.402319] rz-ssi-pcm-audio 1004a000.ssi: DMA enabled
[11-05-03.887][ 3.418738] [drm] Initialized rcar-du 1.0.0 20130110 for 10890000.display on minor 0
[11-05-03.888][ 3.426540] [drm] Device 10890000.display probed
[11-05-04.020][ 3.519665] Console: switching to colour frame buffer device 240x67
[11-05-04.020][ 3.558023] rcar-du 10890000.display: [drm] fb0: rcar-dudrmfb frame buffer device
[11-05-04.088][ 3.600666] mmc0: new HS200 MMC card at address 0001
[11-05-04.088][ 3.606604] mmcblk0: mmc0:0001 G1J38E 59.3 GiB
[11-05-04.088][ 3.611439] mmcblk0boot0: mmc0:0001 G1J38E partition 1 31.5 MiB
[11-05-04.088][ 3.617668] mmcblk0boot1: mmc0:0001 G1J38E partition 2 31.5 MiB
[11-05-04.089][ 3.623941] mmcblk0rpmb: mmc0:0001 G1J38E partition 3 4.00 MiB, chardev (242:0)
[11-05-04.090][ 3.632706] mmcblk0: p1
[11-05-04.121][ 3.673171] ALSA device list:
[11-05-04.148][ 3.676282] #0: rz-ssi-dai-wm8978-hifi
[11-05-04.149][ 3.680299] #1: sound_card
[11-05-04.149][ 3.684245] Waiting for root device /dev/mmcblk1p2...
[11-05-04.277][ 3.810046] mmc1: new ultra high speed SDR104 SDHC card at address 59b4
[11-05-04.277][ 3.817613] mmcblk1: mmc1:59b4 SN32G 29.7 GiB
[11-05-04.280][ 3.823956] mmcblk1: p1 p2
[11-05-04.422][ 3.932194] EXT4-fs (mmcblk1p2): recovery complete
[11-05-04.422][ 3.940179] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
[11-05-04.422][ 3.948484] VFS: Mounted root (ext4 filesystem) on device 179:26.
[11-05-04.422][ 3.955681] devtmpfs: mounted
[11-05-04.426][ 3.961039] Freeing unused kernel memory: 2112K
[11-05-04.426][ 3.965776] Run /sbin/init as init process
[11-05-04.701][ 4.237604] systemd[1]: System time before build time, advancing clock.
[11-05-04.764][ 4.286108] systemd[1]: systemd 244 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
[11-05-04.768][ 4.308379] systemd[1]: Detected architecture arm64.
[11-05-04.796]
[11-05-04.797]Welcome to Poky (Yocto Project Reference Distro) 3.1.26 (dunfell)!
[11-05-04.797]
[11-05-04.813][ 4.349122] systemd[1]: Set hostname to <smarc-rzg2l>.
[11-05-05.181][ 4.711029] systemd[1]: /lib/systemd/system/docker.socket:6: ListenStream= references a path below legacy directory /var/run/, updating /var/run/docker.sock 鈫/run/docker.sock; please update the unit file accordingly.
[11-05-05.387][ 4.827334] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-05.387][ 4.834524] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
[11-05-05.387][ 4.847148] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
[11-05-05.388][ 4.859914] systemd[1]: Created slice system-getty.slice.
[11-05-05.388][ OK ] Created slice system-getty.slice.
[11-05-05.388][ 4.880486] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-05.388][ 4.889440] systemd[1]: Created slice system-serial\x2dgetty.slice.
[11-05-05.388][ OK ] Created slice system-serial\x2dgetty.slice.
[11-05-05.388][ 4.912334] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-05.388][ 4.921080] systemd[1]: Created slice User and Session Slice.
[11-05-05.389][ OK ] Created slice User and Session Slice.
[11-05-05.414][ 4.944760] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[11-05-05.418][ OK ] Started Dispatch Password 鈥s to Console Directory Watch.
[11-05-05.471][ 4.972697] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[11-05-05.472][ OK ] Started Forward Password R鈥ests to Wall Directory Watch.
[11-05-05.472][ 4.996638] systemd[1]: Reached target Host and Network Name Lookups.
[11-05-05.475][ OK ] Reached target Host and Network Name Lookups.
[11-05-05.476][ 5.024464] systemd[1]: Reached target Paths.
[11-05-05.492][ OK ] Reached target Paths.
[11-05-05.523][ 5.048447] systemd[1]: Reached target Remote File Systems.
[11-05-05.524][ OK ] Reached target Remote File Systems.
[11-05-05.540][ 5.076465] systemd[1]: Reached target Slices.
[11-05-05.541][ OK ] Reached target Slices.
[11-05-05.572][ 5.100477] systemd[1]: Reached target Swap.
[11-05-05.573][ OK ] Reached target Swap.
[11-05-05.633][ 5.136169] systemd[1]: Listening on RPCbind Server Activation Socket.
[11-05-05.633][ OK ] Listening on RPCbind Server Activation Socket.
[11-05-05.633][ 5.164484] systemd[1]: Reached target RPC Port Mapper.
[11-05-05.637][ OK ] Reached target RPC Port Mapper.
[11-05-05.666][ 5.194067] systemd[1]: Listening on Syslog Socket.
[11-05-05.666][ OK ] Listening on Syslog Socket.
[11-05-05.718][ 5.220921] systemd[1]: Listening on initctl Compatibility Named Pipe.
[11-05-05.718][ OK ] Listening on initctl Compatibility Named Pipe.
[11-05-05.718][ 5.249314] systemd[1]: Listening on Journal Audit Socket.
[11-05-05.723][ OK ] Listening on Journal Audit Socket.
[11-05-05.774][ 5.277044] systemd[1]: Listening on Journal Socket (/dev/log).
[11-05-05.774][ OK ] Listening on Journal Socket (/dev/log).
[11-05-05.777][ 5.305163] systemd[1]: Listening on Journal Socket.
[11-05-05.777][ OK ] Listening on Journal Socket.
[11-05-05.830][ 5.333269] systemd[1]: Listening on Network Service Netlink Socket.
[11-05-05.831][ OK ] Listening on Network Service Netlink Socket.
[11-05-05.831][ 5.361224] systemd[1]: Listening on udev Control Socket.
[11-05-05.834][ OK ] Listening on udev Control Socket.
[11-05-05.867][ 5.388914] systemd[1]: Listening on udev Kernel Socket.
[11-05-05.867][ OK ] Listening on udev Kernel Socket.
[11-05-05.887][ 5.422311] systemd[1]: Mounting Huge Pages File System...
[11-05-05.887] Mounting Huge Pages File System...
[11-05-05.930][ 5.454100] systemd[1]: Mounting POSIX Message Queue File System...
[11-05-05.931] Mounting POSIX Message Queue File System...
[11-05-05.963][ 5.486015] systemd[1]: Mounting Kernel Debug File System...
[11-05-05.964] Mounting Kernel Debug File System...
[11-05-05.990][ 5.518656] systemd[1]: Mounting Temporary Directory (/tmp)...
[11-05-05.994] Mounting Temporary Directory (/tmp)...
[11-05-06.029][ 5.555598] systemd[1]: Starting Create list of static device nodes for the current kernel...
[11-05-06.036] Starting Create list of st鈥des for the current kernel...
[11-05-06.139][ 5.605023] systemd[1]: Starting Start psplash boot splash screen...
[11-05-06.139] Starting Start psplash boot splash screen...
[11-05-06.170][ 5.638838] systemd[1]: Starting RPC Bind...
[11-05-06.171] Starting RPC Bind...
[11-05-06.171][ 5.688539] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[11-05-06.171][ 5.707133] systemd[1]: Starting Journal Service...
[11-05-06.180] Starting Journal Service...
[11-05-06.220][ 5.740999] systemd[1]: Starting Load Kernel Modules...
[11-05-06.220] Starting Load Kernel Modules...
[11-05-06.247][ 5.773784] systemd[1]: Starting Remount Root and Kernel File Systems...
[11-05-06.253] Starting Remount Root and Kernel File Systems...
[11-05-06.282][ 5.806306] systemd[1]: Starting udev Coldplug all Devices...
[11-05-06.288][ 5.813849] mali_kbase: loading out-of-tree module taints kernel.
[11-05-06.288] Starting udev Coldplug all Devices...
[11-05-06.378][ 5.839962] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-06.378][ 5.856749] systemd[1]: Started Start psplash boot splash screen.
[11-05-06.380][ OK 5.868257] mali 11840000.gpu: Kernel DDK version r45p0-01eac0
[11-05-06.380]0m] Started Start psplash boot splash s[ 5.878332] mali 11840000.gpu: Register LUT 00070000 initialized for GPU arch 0x00070009
[11-05-06.381]creen.
[11-05-06.381][ 5.894011] mali 11840000.gpu: GPU identified as 0x3 arch 7.0.9 r0p0 status 0
[11-05-06.381][ 5.907466] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
[11-05-06.381][ 5.908426] mali 11840000.gpu: No priority control manager is configured
[11-05-06.383][ 5.920429] mali 11840000.gpu: No memory group manager is configured
[11-05-06.449][ 5.939946] systemd[1]: Started RPC Bind.
[11-05-06.449][ 5.940641] random: systemd-journal: uninitialized urandom read (16 bytes read)
[11-05-06.450][ 5.949341] mali 11840000.gpu: Probed as mali0
[11-05-06.450][ 5.951639] random: systemd-journal: uninitialized urandom read (16 bytes read)
[11-05-06.450][ OK 5.964255] rgnmm_drv mmngr: assigned reserved memory node linux,multimedia
[11-05-06.454]0m] Started RPC Bind.
[11-05-06.454][ 5.985164] systemd[1]: Started Journal Service.
[11-05-06.454][ OK ] Started Journal Service.
[11-05-06.544][ OK ] Mounted Huge Pages File System.
[11-05-06.544][ OK ] Mounted POSIX Message Queue File System.
[11-05-06.549][ OK ] Mounted Kernel Debug File System.
[11-05-06.566][ OK ] Mounted Temporary Directory (/tmp).
[11-05-06.588][ OK ] Started Create list of sta鈥nodes for the current kernel.
[11-05-06.604][ OK ] Started Load Kernel Modules.
[11-05-06.626][ OK ] Started Remount Root and Kernel File Systems.
[11-05-06.653] Mounting Kernel Configuration File System...
[11-05-06.671][ OK ] Started Start psplash-syst鈥rogress communication helper.
[11-05-06.698] Starting Flush Journal to Persistent Storage...
[11-05-06.742] Starting Apply Kernel Variables...
[11-05-06.745][ 6.266680] systemd-journald[166]: Received client request to flush runtime journal.
[11-05-06.746] Starting Create Static Device Nodes in /dev...
[11-05-06.775][ OK ] Mounted Kernel Configuration File System.
[11-05-06.796][ OK ] Started Flush Journal to Persistent Storage.
[11-05-06.843][ OK ] Started Apply Kernel Variables.
[11-05-06.876][ OK ] Started Create Static Device Nodes in /dev.
[11-05-06.881][ OK ] Reached target Local File Systems (Pre).
[11-05-06.901] Mounting /var/volatile...
[11-05-06.925] Starting udev Kernel Device Manager...
[11-05-06.941][ OK ] Mounted /var/volatile.
[11-05-06.973] Starting Load/Save Random Seed...
[11-05-07.137][ OK ] Started udev Kernel Device Manager.
[11-05-07.283][ OK ] Started udev Coldplug all Devices.
[11-05-07.673][ 7.208017] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-07.857][ 7.385107] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-07.857][ 7.394593] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-08.187][ OK ] Created slice system-weston.slice.
[11-05-08.277][ 7.812182] random: crng init done
[11-05-08.277][ 7.815600] random: 85 urandom warning(s) missed due to ratelimiting
[11-05-08.315][ OK ] Started Load/Save Random Seed.
[11-05-08.369][ OK ] Reached target Hardware activated USB gadget.
[11-05-08.657][ OK ] Found device /dev/mmcblk1p1.
[11-05-08.689] Mounting /boot...
[11-05-08.735][ 8.270354] FAT-fs (mmcblk1p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[11-05-08.751][ OK ] Mounted /boot.
[11-05-08.768][ OK ] Reached target Local File Systems.
[11-05-08.794] Starting Create Volatile Files and Directories...
[11-05-08.854][ OK ] Started Create Volatile Files and Directories.
[11-05-08.885] Starting Network Time Synchronization...
[11-05-08.909] Starting Update UTMP about System Boot/Shutdown...
[11-05-08.957][ OK ] Started Update UTMP about System Boot/Shutdown.
[11-05-09.150][ OK ] Started Network Time Synchronization.
[11-05-09.226][ OK ] Reached target System Initialization.
[11-05-09.226][ OK ] Started Daily Cleanup of Temporary Directories.
[11-05-09.227][ OK ] Reached target System Time Set.
[11-05-09.230][ OK ] Reached target System Time Synchronized.
[11-05-09.231][ OK ] Reached target Timers.
[11-05-09.252][ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[11-05-09.273][ OK ] Listening on D-Bus System Message Bus Socket.
[11-05-09.306] Starting Docker Socket for the API.
[11-05-09.306][ OK ] Listening on dropbear.socket.
[11-05-09.327][ OK ] Listening on Docker Socket for the API.
[11-05-09.343][ OK ] Reached target Sockets.
[11-05-09.359][ OK ] Reached target Basic System.
[11-05-09.387] Starting Save/Restore Sound Card State...
[11-05-09.408][ OK ] Started Kernel Logging Service.
[11-05-09.447][ OK ] Started System Logging Service.
[11-05-09.472][ OK ] Started D-Bus System Message Bus.
[11-05-09.516] Starting IPv6 Packet Filtering Framework...
[11-05-09.539] Starting IPv4 Packet Filtering Framework...
[11-05-09.564] Starting Network Time Service (one-shot ntpdate mode)...
[11-05-09.580] Starting Telephony service...
[11-05-09.596][ OK ] Started optee services.
[11-05-09.677] Starting Login Service...
[11-05-09.724][ OK ] Started VIN initializing setting.
[11-05-09.724][ OK ] Started WatchdogTimer.
[11-05-09.753][ OK ] Started Save/Restore Sound Card State.
[11-05-09.775][ OK ] Started IPv6 Packet Filtering Framework.
[11-05-09.795][ OK ] Started IPv4 Packet Filtering Framework.
[11-05-09.816][ OK ] Started Network Time Service (one-shot ntpdate mode).
[11-05-09.928][ OK ] Started Telephony service.
[11-05-10.840][ OK ] Started Login Service.
[11-05-10.872][ OK ] Reached target Network (Pre).
[11-05-10.888][ OK ] Reached target Sound Card.
[11-05-10.904] Starting Connection service...
[11-05-10.919] Starting Network Service...
[11-05-11.178][ OK ] Started Network Service.
[11-05-11.206] Starting Wait for Network to be Configured...
[11-05-11.241][ 10.770732] Microchip KSZ9131 Gigabit PHY 11c30000.ethernet-ffffffff:07: attached PHY driver [Microchip KSZ9131 Gigabit PHY] (mii_bus:phy_addr=11c30000.ethernet-ffffffff:07, irq=173)
[11-05-11.284][ OK ] Started Connection service.
[11-05-11.326][ OK ] Reac[ 10.836042] Microchip KSZ9131 Gigabit PHY 11c20000.ethernet-ffffffff:07: attached PHY driver [Microchip KSZ9131 Gigabit PHY] (mii_bus:phy_addr=11c20000.ethernet-ffffffff:07, irq=172)
[11-05-11.327]hed target Network.
[11-05-11.327][ OK ] Reached target Network is Online.
[11-05-11.368] Starting Avahi mDNS/DNS-SD Stack...
[11-05-11.372][ 10.902069] audit: type=1325 audit(1600598644.660:2): table=filter family=2 entries=4 op=xt_replace pid=237 comm="connmand"
[11-05-11.389] Starting Wait for network to be configured by ConnMan...
[11-05-11.417] Starting LSB: start and stop docker...
[11-05-11.439] Starting Docker Application Container Engine...
[11-05-11.455] Starting Network Time Service...
[11-05-11.471] Starting Permit User Sessions...
[11-05-11.509] Starting Target Communication Framework agent...
[11-05-11.559][ 11.088747] audit: type=1325 audit(1600598644.848:3): table=nat family=2 entries=5 op=xt_replace pid=237 comm="connmand"
[11-05-11.601][ OK ] Started Permit User Sessions.
[11-05-11.629][ OK ] Started LSB: start and stop docker.
[11-05-11.650][ OK ] Started Avahi mDNS/DNS-SD Stack.
[11-05-11.713][ OK ] Started Getty on tty1.
[11-05-11.745][ OK ] Started Serial Getty on ttySC0.
[11-05-11.763][ OK ] Reached target Login Prompts.
[11-05-11.779] Starting Hostname Service...
[11-05-11.809] Starting WPA supplicant...
[11-05-11.836][ OK ] Started Target Communication Framework agent.
[11-05-11.978][ OK ] Started Network Time Service.
[11-05-12.058][ OK ] Started Hostname Service.
[11-05-12.091][ OK ] Started WPA supplicant.
[11-05-14.731][ 14.187290] audit: type=1325 audit(1600598647.944:4): table=nat family=2 entries=5 op=xt_replace pid=311 comm="iptables"
[11-05-14.732][ 14.203025] audit: type=1325 audit(1600598647.960:5): table=filter family=2 entries=4 op=xt_replace pid=313 comm="iptables"
[11-05-14.732][ 14.215506] audit: type=1325 audit(1600598647.972:6): table=filter family=2 entries=6 op=xt_replace pid=315 comm="iptables"
[11-05-14.733][ 14.229425] audit: type=1325 audit(1600598647.984:7): table=filter family=2 entries=8 op=xt_replace pid=317 comm="iptables"
[11-05-14.733][ 14.242907] audit: type=1325 audit(1600598648.000:8): table=filter family=2 entries=10 op=xt_replace pid=319 comm="iptables"
[11-05-14.734][ 14.257552] audit: type=1325 audit(1600598648.016:9): table=filter family=2 entries=11 op=xt_replace pid=321 comm="iptables"
[11-05-14.735][ 14.268974] audit: type=1325 audit(1600598648.020:10): table=filter family=2 entries=12 op=xt_replace pid=322 comm="iptables"
[11-05-14.822][ 14.351520] audit: type=1325 audit(1600598648.108:11): table=nat family=2 entries=7 op=xt_replace pid=328 comm="iptables"
[11-05-15.788][ 15.322702] process 'docker/tmp/qemu-check235759621/check' started with executable stack
[11-05-15.849][ OK ] Started Docker Application Container Engine.
[11-05-15.867][ OK ] Reached target Multi-User System.
[11-05-15.899] Starting Update UTMP about System Runlevel Changes...
[11-05-15.923][ OK ] Started Weston Wayland Compositor.
[11-05-15.970][ OK ] Started Update UTMP about System Runlevel Changes.
[11-05-16.011][ OK ] Created slice User Slice of UID 0.
[11-05-16.035] Starting User Runtime Directory /run/user/0...
[11-05-16.075][ OK ] Started User Runtime Directory /run/user/0.
[11-05-16.092] Starting User Manager for UID 0...
[11-05-17.757]
[11-05-17.757]Poky (Yocto Project Reference Distro) 3.1.26 smarc-rzg2l ttySC0
[11-05-17.757]
[11-05-17.757]BSP: RZG2L/RZG2L-SMARC-EVK/3.0.5
[11-05-17.757]LSI: RZG2L
[11-05-17.760]Version: 3.0.5
[11-06-53.958]smarc-rzg2l login: root
[11-06-53.990]Last login: Sun Sep 20 10:44:09 UTC 2020
[11-06-54.178]numid=59,iface=MIXER,name='Left Input Mixer L2 Switch'
[11-06-54.178] ; type=BOOLEAN,access=rw------,values=1
[11-06-54.178] : values=on
[11-06-54.178]numid=62,iface=MIXER,name='Right Input Mixer R2 Switch'
[11-06-54.178] ; type=BOOLEAN,access=rw------,values=1
[11-06-54.178] : values=on
[11-06-54.178]numid=41,iface=MIXER,name='Headphone Playback Volume'
[11-06-54.179] ; type=INTEGER,access=rw---R--,values=2,min=0,max=63,step=0
[11-06-54.179] : values=63,63
[11-06-54.179] | dBscale-min=-57.00dB,step=1.00dB,mute=0
[11-06-54.180]numid=5,iface=MIXER,name='PCM Volume'
[11-06-54.180] ; type=INTEGER,access=rw---R--,values=2,min=0,max=255,step=0
[11-06-54.180] : values=255,255
[11-06-54.180] | dBscale-min=-127.50dB,step=0.50dB,mute=1
[11-06-54.181]numid=48,iface=MIXER,name='Input PGA Volume'
[11-06-54.182] ; type=INTEGER,access=rw---R--,values=2,min=0,max=63,step=0
[11-06-54.182] : values=25,25
[11-06-54.182] | dBscale-min=-12.00dB,step=0.75dB,mute=0
[11-06-54.839]root@smarc-rzg2l:~#
五 参考
https://www.renesas.com/us/en/products/microcontrollers-microprocessors/rz-mpus/rzg2l-getting-started
相关文章：
瑞萨RZ/G2L平台 初起动（SD卡启动）
文章目录 一 准备条件1 工具2 硬件3 镜像 二 烧录SD卡启动盘三 写Bootloader1 烧录文件2 启动烧录3 烧录 四 启动设置 一 准备条件 1 工具 ** BalenaEtcher（俗称“ Etcher”），是一款快速将系统镜像文件（ .iso 或 .img 或 .zip或…...
chkconfig及服务脚本
运行级别 linux启动之后处于某个状态 linux运行级别 0：关机 #设置即重启 1：单用户，为root权限，禁止远程登录 2：无网络文本模式 3：多用户文本模式 4：未使用 5：图形化…...
[Android] libcutils - native 获取/设置 property
前言： Android 的property系统类似于linux的环境变量，但是更加精细。可以通过adb 设置和读取 property，同时也可以在代码 (JAVA/C/C) 中设置和获取属性。这有助于我们在运行时控制代码执行逻辑。比如打开 测试开关 或者 dump源数据文件。 工…...
Matlab 方位角计算之二
文章目录 一、简介二、实现代码三、实现效果一、简介 我们总是说降维打击，这种思路尤其在一些问题上显现的尤为突出，就比如方位角这个问题，如果我们局限于二维这个空间，那么很多时候就需要判断方向向量落在了那个象限，之后再一个个情况逐一分析，虽然这样做并不复杂，但总…...
Postman工具简介
介绍 Postman是一个商业的接口测试工具。免费的版本也可以使用不少功能。 官网：https://www.postman.com/ 下载、安装、应用界面 下载 安装、安装成功以后的应用界面 双击下载下来的可执行文件进行安装，出现如下界面： 可以注册一个账…...
2023.11.17 -hivesql调优,数据压缩,数据存储
目录 1.hive命令和参数配置 2.hive数据压缩 3.hive数据存储 0.原文件大小 18.1MB 1.textfile行存储格式, 压缩后size:18MB 2.行存储格式:squencefile ,压缩后大小8.89MB 3. 列存储格式 orc - ZILIB ,压缩后大小2.78MB 4.列存储格式 orc-snappy ,压缩后大小3.75MB 5…...
基于Vue+SpringBoot的大学计算机课程管理平台 开源项目
目录 一、摘要1.1 项目介绍1.2 项目录屏 二、功能模块2.1 实验课程档案模块2.2 实验资源模块2.3 学生实验模块 三、系统设计3.1 用例设计3.2 数据库设计3.2.1 实验课程档案表3.2.2 实验资源表3.2.3 学生实验表 四、系统展示五、核心代码5.1 一键生成实验5.2 提交实验5.3 批阅实…...
2.c++基础语法
文章目录 1.c 程序结构关键字标识符、操作符、标点预处理指令注释main 主函数命名空间 2.c 变量和常量变量 3.c 数组和容器4.c 程序流程5.c字符和字符串 1.c 程序结构 关键字 关键字事程序保留的，程序员不能使用，c的常见关键字如下图： 标识…...
applicationContext.getBean 为null
场景： 使用SpringUtils 添加了统一类的调用。单元测试是正常的。 SpringUtils public class SpringUtils implements ApplicationContextAware {private static ApplicationContext applicationContext;Overridepublic void setApplicationContext(Nonnull Applica…...
无线WiFi安全渗透与攻防(六)之WEP破解-Gerix-wifi-cracker自动化破解WEP加密
WEP破解-Gerix-wifi-cracker自动化破解WEP加密 WEP破解-Gerix-wifi-cracker自动化破解WEP加密1.环境准备1.软件和kali2.下载软件，下载地址3.将软件复制到kali，解压4.进入软件目录2.破解步骤1.启动gerix-wifi-cracker-2-master软件2.设置无线网卡位Monitor Mode模式3.重新扫描…...
华为OD机试 - 环中最长子串（Java JS Python C）
题目描述 给你一个字符串 s，首尾相连成一个环形，请你在环中找出 o 字符出现了偶数次最长子字符串的长度。 输入描述 输入是一个小写字母组成的字符串 输出描述 输出是一个整数 备注 1 ≤ s.length ≤ 500000s 只包含小写英文字母用例 输入alolobo输出6说明最长子字符串之一…...
bug-跨域访问问题
问题场景 自定义 header，导致跨域问题 一个大屏项目，设置请求接口获取数据时，有的接口能够正常返回数据，有的接口提示跨域（接口域名不同），后端也进行支持跨域设置，结果还是提示跨域…...
Babyk勒索病毒数据集恢复，计算机服务器中了babyk勒索病毒怎么办？
计算机网络技术的不断应用，为企业的生产运营提供了极大便利，网络技术的不断发展也带来了许多网络安全隐患，近期，云天数据恢复中心陆续接到许多企业的求助，企业的计算机服务器遭到了babyk勒索病毒的攻击，导致…...
（.htaccess文件特性）[MRCTF2020]你传你呢 1
题目环境： 不难看出是一道文件上传漏洞 上传一句话木马文件burpsuite进行抓包<?php eval($_POST[shell]);?> 命名为PHP文件格式 Repeater进行重放 尝试了其它后缀进行绕过都没有成功 通过 application/x-php内容类型，可以看出被识别出是PHP文件&…...
微软Ignite 2023大盘点：GPT-4 Turbo、DALL-E 3等
11月16日，微软在美国西雅图举办“Microsoft Ignite 2023”全球开发者大会。ChatGPT等生成式AI成为了本次大会的重要主题。 下面「AIGC开放社区」将根据大会发布的内容，盘点重要内容。 GPT-4 Turbo、 DALL E 3等全新模型 16K上下文的新GPT-3.5 Turbo模…...
应用架构的演进 I 使用无服务器保证数据一致性
在微服务架构中，一个业务操作往往需要跨多个服务协作完成，包含了读取数据和更新多个服务的数据同时进行。在数据读取和写入的过程中，有一个服务失败了，势必会造成同进程其他服务数据不一致的问题。 亚马逊云科技开发者社区为开发者…...
jupyter修改默认打开目录
当我们打开jupyter notebook（不管用什么样的方式打开，使用菜单打开或者是命令行打开是一样的）会在默认的浏览器中看到这样的界面、 但是每一台不同的电脑打开之后的界面是不同的，仔细观察就会发现，这里面现实的一些文件…...
HTML5学习系列之标题和正文、描述性信息
HTML5学习系列之标题和正文、描述性信息 标题和正文标题段落 描述性信息强调注解备选上下标术语代码预定义格式缩写词编辑提示引用引述换行显示修饰非文本注解 总结 标题和正文 标题 按语义轻重排列：h1\h2\h3\h4\h5\h6 <h1>诗词介绍</h1> <h2>…...
互联网医院系统：数字化时代中医疗服务的未来
随着数字化时代的发展，互联网医院系统在医疗服务中的作用日益凸显。本文将讨论互联网医院系统的一些关键技术方面，探讨这些技术如何推动医疗服务进入数字化时代。 1. 数据智能与个性化服务 互联网医院系统依赖于大数据分析和人工智能技术，…...
（C语言）输入一个序列，判断是否为奇偶交叉数
#include <stdio.h> #include <string.h> int main() {char str[50];gets(str);int len,tmp 1;len strlen(str); //获取字符串长度 for (int i 0;i < len-1 ;i ){if((str[i] % 2 0 ) && (str[i1] % 2 ! 0)) //判断先偶数后奇数序列 tmp ;else if((s…...
蓝桥杯模拟赛：最远滑行距离 ← dfs
【题目来源】https://www.lanqiao.cn/problems/2414/learning/【题目描述】 小蓝准备在一个空旷的场地里面滑行，这个场地的高度不一，小蓝用一个 n 行 m 列的矩阵来表示场地，矩阵中的数值表示场地的高度。 如果小蓝在某个位置，而他…...
广东电信手机号余额查询接口
接口地址：https://gdty.gd189.cn/MOService/mapi/moduleRecharge/recharge/querySerCount 请求参数： {"mphone":"15303*05139","mareaCode":"","busiId":"CDMA","chongzhiType&qu…...
这次轮到微软炸场了；5000+AI工具调研报告 (500万字)；狂打一星开喷AI聊天机器人；CMU LLM课程；AI创业的方向与时机 | ShowMeAI日报
👀日报&周刊合集 | 🎡生产力工具与行业应用大全 | 🧡 点赞关注评论拜托啦！ 🉑 Microsoft Ignite 2023 技术大会：微软的年度炸场时刻，而且连炸四天 https://ignite.microsoft.com OpenAI 开发…...
--max-old-space-size=8192报错
vue项目运行时，如果经常运行慢，崩溃停止服务，报如下错误 FATAL ERROR: CALL_AND_RETRY_LAST Allocation failed - JavaScript heap out of memory 因为在 Node 中，通过JavaScript使用内存时只能使用部分内存（64位系统&…...
单区域OSPF配置
配置命令步骤： 1.使用router ospf 进程ID编号 启用OSPF路由 2.使用network 直连网络地址 反掩码 area 0 将其归于区域0 注意：1.进程ID编号可任意（1-65535）2.反掩码用4个255相减得到 如下图，根据给出要求配置OSPF单区…...
VsCode 安装 GitHub Copilot插件 （最新）
##在线安装： 打开Vscode扩展商店，输入 "GitHub Copilot " ,选择下载人数最多的那个。（这个是你写一部分代码或者注释，Ai自动帮你提示/补全代码）,建议选择这个 注意下面有个和他类似的 "GitHub Copilo…...
人工智能基础_机器学习039_sigmoid函数_逻辑回归_逻辑斯蒂回归_分类神器_代码实现逻辑回归图---人工智能工作笔记0079
逻辑斯蒂回归（Logistic Regression）是一种常用的分类算法，其基本思想是通过拟合一个逻辑斯蒂函数来预测样本所属的类别。它广泛应用于各个领域，如医学、金融、市场营销等，具有较好的解释性和可解释性。在逻辑斯蒂回归中，我们通常使用的是二分类问题，即样本只属于两个类别…...
购买阿里云服务器需要多少钱？活动价3000元-5000元的阿里云服务器汇总
购买阿里云服务器需要多少钱？如果我们只有3000元-5000元的预算可以购买什么实例规格和配置的阿里云服务器呢？因为阿里云服务器价格是由实例规格、配置、带宽等众多配置决定的，所以，目前阿里云活动中的价格在3000元-5000元的云服务…...
CentOS修改root用户密码
一、适用场景 1、太久没有登录CentOS系统，忘记管理密码。 2、曾经备份的虚拟化OVA或OVF模板，使用模板部署新系统后，忘记root密码。 3、被恶意攻击修改root密码后的紧急修复。 二、实验环境 1、VMware虚拟化的ESXI6.7下，通过曾经…...
Android消息机制（Handler、Looper、MessageQueue）
一、ThreadLocal 1、什么是ThreadLocal ThreadLocal 是一个线程内部的数据存储类，通过它可以在指定的线程中存储数据，数据存储以后，只有在指定线程中可以获取到存储的数据，对于其他线程来说则无法获取到数据。 一般来说…...